View CXA1560S_23492.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

CXA1560S, CXA1561M/S, CXA1562M/S
Dolby B-C Type Noise Reduction System
Description The CXA1560 series is a bipolar IC incorporating stereo Dolby B-C type noise reduction (NR) system. Five kinds of device are provided due to the combination of three line output levels and two packages for various applications. A reduction in the number of external parts and small package have been achieved due to the fact that the spectral skewing circuits are all on-chip. Features * Few external parts * Spectral skewing circuit are on-chip * NR ON/OFF, REC/PB, MPX filter ON/OFF switches * Small package (24-pin SOP, 22-pin SDIP) * Low current consumption 13mA Typ. (power supply 6V) Structure Bipolar silicon monolithic IC Absolute Maximum Ratings (Ta = 25C) 17 * Supply voltage Vcc - VEE * Operating temperature Topr -40 to +85 * Storage temperature Tstg -65 to +150 * Allowable power dissipation PD 600 (SOP) 1200 (SDIP) CXA1561M CXA1562M 24 pin SOP (Plastic) CXA1560S CXA1561S CXA1562S 22 pin SDIP (Plastic)
V C C mW mW
This IC is available only to the licensees of Dolby Laboratories Licensing Corporation from whom licensing and applications information may be obtained. "Dolby" and the double D symbols are trademarks of Dolby Laboratories Licensing Corporation.
Sony reserves the right to change products and specifications without prior notice. This information does not convey any license by any implication or otherwise under any patents or other right. Application circuits shown, if any, are typical examples illustrating the operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits.
-1-
E93805B5X-PP
Block Diagram and Pin Configuration
P13 LINEOUT1
PBIN1 P12 C11 1 C12 1 R11 3.3k C13 1 C14 100n C15 68n C16 1 P2 VCC
MPX Filter
PBIN1
LINEIN1
RECOUT1
P14 RECOUT1
MPXIN1
MODE
P3 MODE
13 12
LINEIN1 P11
R12 6.8k
MPXOUT1
LINEOUT1
VCT
TCH1
22 20
21 16
19 18 17 15 14
TCL1
SSK
REC AMP
VCC
VCC C1 10
MOA
HLS
HDET
LDET
LLS Mode Control
IREF
PBIN2
TCH2
TCL2
LINEIN2
MPXIN2
R1 20k MPX Filter R22 6.8k
C21 1
C22 1
MPXOUT2
LINEOUT2
R21 3.3k
C23 1
C24 100n
C25 68n
RECOUT2
C26 1 P1 VEE
PBIN2 P22
CXA1560S, CXA1561M/S, CXA1562M/S
Note) This figure shows SDIP package. For SOP package, refer to the Pin Description or Application Circuit.
LINEOUT2 P23
RECOUT2 P24
NRSW P5
LINEIN2 P21
NRSW
VEE
-2-
MOA HLS HDET LDET LLS SSK REC AMP 2 3 4 5 6 7 8 9
IREF VEE
C2 10
1
10
11
CXA1560S, CXA1561M/S, CXA1562M/S
Pin Description and Equivalent Circuit Pin No. SOP SDIP
VCC
Symbol
Z: Imp
VDC (V)
Equivalent circuit
Description
1
1
IREF
0
VEE + 1.25V
VEE + 1.25V
Reference current pin for setting internal filter cut-off frequency
VEE VCC
2, 23 2, 21 PB IN
40k
VCT
Playback input pin Reference level = -30dBm
40K
VCT Buffer amplifier input pin to drive multiplex filter Reference level = -19dBm
VEE VCC
4, 21 4, 19 MPX IN
VCT 62k
3, 22 3, 20 LINE IN
62K
VCT
Recording input pin Reference level = -25dBm
VEE VCC
500
5, 20 5, 18 MPX OUT
0
VCT
8.8k 500
Buffer amplifier output pin to drive multiplex filter Reference level = -15dBm
VEE
-3-
CXA1560S, CXA1561M/S, CXA1562M/S
Pin No. SOP SDIP
Symbol
Z: Imp
VDC (V)
Equivalent circuit
VCC
Description
200
6, 19 6, 17 LINE OUT
0
VCT
200
Line output pin
VEE VCC
7, 15 7, 16 TCH
--
VEE + 0.4V
13k
36k
Time constant connecting pin for HLS detector
330k
VEE VCC
8, 17 8, 15 TCL
--
VEE + 0.4V
13.5k
Time constant connecting pin for LLS detector
480k
VEE VCC
200
9, 16 9, 14 REC OUT
0
VCT
200
Recording output pin Reference level = -6dBm
VEE
-4-
CXA1560S, CXA1561M/S, CXA1562M/S
Pin No. SOP SDIP
Symbol
Z: Imp
VDC (V)
Equivalent circuit
VCC 50A
Description
10
10
NRSW
--
--
50k
22k
NR control pin H: C type M: B type L: NR OFF
VEE
11 14
11 12
VEE VCC
VEE VCC
VCC 50A
Dual power supply: VEE Single power supply: GND pin Vcc
15
13
MODE
--
--
50k
22k
MODE control pin H: REC (Filter ON) M: REC (Filter OFF) L: PB
VEE
24
22
VCT
0
VCT
Dual power supply: GND Single power supply: Vcc/2
-5-
CXA1560S, CXA1561M/S, CXA1562M/S
Electrical Characteristics Ta = 25C, Dolby level: -6dBm (= 388mVrms) at REC OUT, VCC = 15V (CXA1560), VCC = 12V (CXA1561), VCC = 9V (CXA1562) Characteristics Operating voltage CXA1560 CXA1561 CXA1562 Current consumption CXA1560 CXA1561 CXA1562 LINE OUT level CXA1560 CXA1561 CXA1562 LINE IN level PB IN level MPX amplifier gain Encode characteristics B type boost (1) (2) (3) (4) C type boost (1) (2) (3) (4) (5) (6) C-R-1 C-R-2 C-R-3 C-R-4 C-R-5 C-R-6 REC REC REC REC REC REC C C C C C C 500 500 2k 2k 5k 10k -60dB -25dB -60dB -25dB -25dB 0dB 14.2 7.2 18.7 5.4 3.5 -5.5 16.2 9.2 20.7 7.4 5.5 -3.5 18.2 11.2 22.7 9.4 7.5 -1.5 dB dB dB dB dB dB B-R-1 B-R-2 B-R-3 B-R-4 REC REC REC REC B B B B 500 5k 10k 10k -25dB -25dB -40dB 0dB 1.4 3.9 9.7 -1.1 2.9 5.4 10.4 0.4 4.4 6.9 11.4 1.9 dB dB dB dB Symbol R/P Measurement conditions NR f (Hz) Other conditions 11.5 8.5 7.2 8.0 8.0 8.0 -1.0 -4.0 -7.0 -27 -32 9.0 -- -- -- 13.2 13.0 12.8 0.0 -3.0 -6.0 -25 -30 10.0 16.0 16.0 16.0 18.0 18.0 18.0 1.0 -2.0 -5.0 -23 -28 11.0 V V V mA mA mA dBm dBm dBm dBm dBm dB Min. Typ. Max. Unit
Vopr
--
--
--
ICC
REC OFF
--
No Signal
Vlout
REC OFF
1k
Vlin Vpin Gmpx
REC OFF PB OFF
1k 1k 1k
MPX OFF
-6-
CXA1560S, CXA1561M/S, CXA1562M/S
Characteristics Signal handling CXA1560 CXA1561 CXA1562 Total harmonic distortion 1) NR OFF CXA1560 CXA1561 CXA1562 2) B CXA1560 CXA1561 CXA1562 3) C CXA1560 CXA1561 CXA1562 S/N REC-PB PB-REC REC ch to ch REC OUT offest Voltage (OFF-C type)
Symbol R/P
Measurement conditions NR f (Hz) Other conditions
Min.
Typ.
Max.
Unit
Vomax
REC OFF
1k
THD = 1%
13.5 13.5 13.5
16.0 16.2 16.0
-- -- --
dB dB dB
THD (OFF)
REC OFF
1k
+10dB
-- -- -- -- -- -- -- -- -- 60 -- -- -- -100
0.03 0.02 0.02 0.03 0.03 0.04 0.04 0.04 0.05 64 -80 -87 -73 0
0.1 0.1 0.1 0.1 0.1 0.1 0.2 0.2 0.2 -- -70 -70 -65 100
% % % % % % % % % dB dB dB dB mV
THD (B)
REC
B
1k
+10dB
THD (C) SN (CCIR) CT-1 CT-2 CT-3 Voff
REC
C
1k
+10dB
REC
C
-- 1k 1k 1k --
Rg = 5 (CCIR/ARM) 0dB 0dB 0dB
PB OFF REC OFF REC OFF REC OFF C
0dB means the level which provides the Dolby level to recording output when NR is off.
-7-
Electrical Characteristics Measurement Circuit
S12 R12 6.8k S2-1 C16 1
S1-1
S11 C11 1 VMODE 14 13 12 21 20 16 19 18 17 15 C12 1 R11 3.3k C13 1 C14 100n C15 68n
DC Volt Meter
C2 100
22
VCT
PBIN1
TCH1
TCL1
LINEIN1
MPXIN1
MPXOUT1
LINEOUT1
RECOUT1
MODE
VCC
VCC
PBIN2
MPXOUT2
IREF
MPXIN2
TCH2
LINEIN2
LINEOUT2
RECOUT2
NRSW
TCL2
GND
-8-
CXA1560S/A1561S/A1562S 2 3 C21 1 C22 1 R21 3.3k C23 1 C24 100n C25 68n VNRSW R22 6.8k 7 4 8 5 6 9 10 11 C26 1 S1-2
Audio SG
A
C1 100
1
R1 20k
S21 S2-2 S3 CCIR/ARM Filter Audio Analyzer
CXA1560S, CXA1561M/S, CXA1562M/S
S22
Application Circuit Switchable Processor with Dual Power Supply (CXA1560S/1561S/1562S)
LINEIN1 P11 P14 RECOUT1 MPX Filter MPX OFF MPX ON 13 12
R12 6.8k (5%) P13 LINEOUT1 R11 3.3k (5%)
PBIN1 P12
C11 1
C12 1
C13 1
C14 100n (10%) 16 15 14
C15 68n (10%)
PB C16 1
P2 VCC
22 20
21
19 18 17
VCC
VCT
PBIN1
TCH1
TCL1
LINEIN1
MPXIN1
MPXOUT1
PBIN2
IREF
LINEIN2
MPXIN2
TCH2
TCL2
MPXOUT2
LINEOUT2
RECOUT2
NRSW
VEE
-9-
CXA1560S/1561S/1562S 3 4 7 8 5 6 9 10 C22 1 C23 1 OFF C26 1 B C24 100n (10%) C25 68n (10%) C MPX Filter R22 6.8k (5%) R21 3.3k (5%)
LINEOUT1
RECOUT1
MODE
C1 10
C2 10 11
1
2
R1 20k (2%)
C21 1
P1 VEE P24 RECOUT2 P23 LINEOUT2
PBIN2 P22
LINEIN2 P21
CXA1560S, CXA1561M/S, CXA1562M/S
Note) Resistor and capacitor tolerances are 10% and 20% respectively, unless otherwise specified. Application circuits shown are typical examples illustrating the operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits or for any infringement of third party patent and other right due to same.
Switchable Processor with Dual Power Supply (CXA1561M/1562M)
LINEIN1 P11 MPX Filter MPX OFF MPX ON 15 14 13
R12 6.8k (5%) P13 LINEOUT1 R11 3.3k (5%) P14 RECOUT1
PBIN1 P12
C11 1
C12 1
C13 1
C14 100n (10%) 18 17 16
C15 68n (10%)
PB C16 1
P2 VCC
24
23 20
22
21
19
VCC
VCT
PBIN1
TCH1
TCL1
LINEIN1
MPXIN1
MPXOUT1
MPXOUT2
LINEOUT2
RECOUT2
PBIN2
IREF
LINEIN2
MPXIN2
TCH2
TCL2
NRSW
VEE
N.C.
- 10 -
CXA1561M/1562M 3 4 7 8 5 6 9 10 11 C22 1 C23 1 OFF C26 1 B C24 100n (10%) C25 68n (10%) C MPX Filter R22 6.8k (5%) R21 3.3k (5%)
LINEOUT1
RECOUT1
MODE
N.C.
C1 10
C2 10 12
1
2
R1 20k (2%)
C21 1
P1 VEE P24 RECOUT2 P23 LINEOUT2
PBIN2 P22
LINEIN2 P21
Note) Resistor and capacitor tolerances are 10% and 20% respectively, unless otherwise specified. Application circuits shown are typical examples illustrating the operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits or for any infringement of third party patent and other right due to same.
CXA1560S, CXA1561M/S, CXA1562M/S
Switchable Processor with Single Power Supply (CXA1560S/1561S/1562S)
LINEIN1 P11 P14 RECOUT1 MPX Filter MPX OFF MPX ON 13 12 P2 VCC
R12 6.8k (5%) P13 LINEOUT1 R11 3.3k (5%)
PBIN1 P12
C11 1
C12 1
C13 1
C14 100n (10%) 16 15 14
C15 68n (10%)
PB C16 1
22 20
21
19 18 17
VCT
PBIN1
TCH1
TCL1
MODE
VCC
LINEIN1
MPXIN1
MPXOUT1
CXA1560S/1561S/1562S
LINEOUT1
RECOUT1
C1 10
PBIN2
IREF
LINEIN2
MPXIN2
TCH2
TCL2
MPXOUT2
LINEOUT2
1 3 4 7 8
2
5
6 9
RECOUT2
10
NRSW
11
VEE
- 11 -
C22 1 C23 1 OFF C26 1 B C24 100n (10%) C25 68n (10%) C MPX Filter R22 6.8k (5%) R21 3.3k (5%)
C2 47
R1 20k (2%)
C21 1
P1 GND P24 RECOUT2 P23 LINEOUT2
PBIN2 P22
LINEIN2 P21
Note) Resistor and capacitor tolerances are 10% and 20% respectively, unless otherwise specified.
CXA1560S, CXA1561M/S, CXA1562M/S
Application circuits shown are typical examples illustrating the operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits or for any infringement of third party patent and other right due to same.
Switchable Processor with Single Power Supply (CXA1561M/1562M)
LINEIN1 P11 MPX Filter MPX OFF MPX ON 15 14 13
R12 6.8k (5%) P13 LINEOUT1 R11 3.3k (5%) P14 RECOUT1
PBIN1 P12
C11 1
C12 1
C13 1
C14 100n (10%) 18 17 16
C15 68n (10%)
PB C16 1
P2 VCC
24
23
22 20
21
19
VCT
VCC
PBIN1
TCH1
TCL1
MODE
N.C.
LINEIN1
MPXIN1
MPXOUT1
CXA1561M/1562M
LINEOUT1
RECOUT1
C1 10
PBIN2
IREF
LINEIN2
MPXIN2
TCH2
TCL2
MPXOUT2
LINEOUT2
RECOUT2
NRSW
VEE
1 4 7 8 10
2
3
5
6 9
11
N.C.
12
- 12 -
C22 1 C23 1 OFF C26 1 B C24 100n (10%) C25 68n (10%) C MPX Filter R22 6.8k (5%) R21 3.3k (5%)
C2 47
R1 20k (2%)
C21 1
P1 GND P24 RECOUT2 P23 LINEOUT2
PBIN2 P22
LINEIN2 P21
Note) Resistor and capacitor tolerances are 10% and 20% respectively, unless otherwise specified. Application circuits shown are typical examples illustrating the operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits or for any infringement of third party patent and other right due to same.
CXA1560S, CXA1561M/S, CXA1562M/S
CXA1560S, CXA1561M/S, CXA1562M/S
Application Note The CXA1560 series is a stereo Dolby B-C type NR IC like the CXA1330 series. Built-in spectral skewing circuit allows smaller package. 1) Power Supply The CXA1560 series is designed to operate on either single or dual power supply. For dual power supply, connect VCT to GND, and VEE to the negative power supply. For single power supply, connect VEE to GND. Vcc/2, generated from the internal circuit, is output to VCT. Connect a by-pass capacitor between this pin and GND. The operating voltage range is 3.5 to 8.0V (7.0 to 16V), which satisfies the signal handling of 12dB specified by the Dolby Laboratories. 2) Operation Mode Control The CXA1560 series has built-in electronic switches. The operations are controlled by the DC voltages of NRSW and MODE control pins. Table 1 shows the switching truth tables. For single power supply, VH, VM, and VL correspond to Vcc, Vcc/2 and GND, respectively. For dual power supply, VH, VM and VL correspond to Vcc, GND and VEE, respectively. Refer to "threshold" on the characteristics graph for the thresholds of the control voltages. NRSW and MODE control pins are connected to VCT via a 50k resistor, so when the pin is open, VM condition results. VH NRSW MODE C type MPX ON REC (Encode) VM B type MPX OFF REC (Encode) Table 1 3) Reference level The CXA1560 series Dolby level is -6dBm (388mVrms), and is measured at the recording output pin (REC OUT) in the NR OFF mode. The reference level of the recording input pin (LINE IN), playback input pin (PB IN) and line output pin (LINE OUT) are defined as the levels which provide Dolby level at the recording output pin in NR OFF mode. 4) MPX Filter The CXA1560 series provides an MPX (FM multiplex) filter ON/OFF function. Connect the MPX filter between MPX IN and MPX OUT. In MPX ON mode, the line input signal is fed to the NR processor via the MPX buffer amplifier and MPX filter. In MPX OFF mode, the signal bypasses the buffer amplifier and filter, and is fed directly to the NR processor. The MPX buffer amplifier gain is 10dB. The gain from LINE IN to LINE OUT is 19dB, and from MPX IN to LINE OUT it is 13dB, for a deviation of 6dB. This means that if a filter with insertion loss of 4dB is used, there is no fluctuation between MPX ON and MPX OFF. VL NR OFF PB (Decode)
- 13 -
CXA1560S, CXA1561M/S, CXA1562M/S
Example of Representative Characteristics
Quiescent current consumption vs. Supply voltage
ICC-Quiescent current consumptionl [mA]
Encode Mode 15 16
Current consumption vs. Input level
Encode Mode VCC = 6V 0dB = Dolby Level Bf = 10k Cf = 10k
ICC-Current consumption [mA]
15 14 13 12 11 10
14 13 12 11 10 8 4 6
B type
NR OFF
C type
NR OFF Bf = 1k
Cf = 1k
8 10 12 14 16 VCC-VEE-Supply voltage [V]
-12
-8
-4 0 4 Input level [dB]
8
12
B type encode characteristics
12 10 VCC = 6V 0dB = Dolby Level -40dB 24 20
C type encode characteristics
VCC = 6V 0dB = Dolby Level
-60dB -50dB
Encode boost [dB]
8 6 4 2 0
Encode boost [dB]
-30dB
16 12 8 4 0 0dB
-40dB
-20dB -10dB 0dB
-30dB -20dB -10dB
100 200
500 1k 2k 5k Frequency [Hz]
10k
20k
100 200
500 1k 2k 5k Frequency [Hz]
10k 20k
Signal handling
Encode Mode f = 1kHz THD = 1% 0dB = Dolby Level A1562 16
Load characteristics
Encode Mode VCC = 6V THD = 1% f = 1kHz NR OFF
Signal handling [dB]
A1561 A1560 10
Maximum output level [dBm]
20
14 12 10 8 6 4
0
NR OFF C type 4 6 8 10 12 14 16 VCC-VEE-Supply voltage [V]
LINE OUT 200
REC OUT 10k
500 1k 2k 5k Load resistance []
- 14 -
CXA1560S, CXA1561M/S, CXA1562M/S
NR OFF total harmonic distortion-1 (CXA1561)
Encode Mode VCC = 6.0V 0dB = Dolby Level 0.1
NR OFF total harmonic distortion-2 (CXA1560)
Encode Mode f = 1kHz 0dB = Dolby Level 0.1
Distortion [%]
f = 100Hz f = 10kHz f = 1kHz
Distortion [%]
VCC = 5.5V 0.01
VCC = 8.0V
0.01
-4
0
4 8 12 16 Output level [dB]
20
-4
0
4 8 12 16 Output level [dB]
20
B type total harmonic distortion-1 (CXA1561)
Encode Mode VCC = 6.0V 0dB = Dolby Level 0.1 f = 100Hz
B type total harmonic distortion-2 (CXA1560)
Encode Mode f = 1kHz 0dB = Dolby Level 0.1
Distortion [%]
Distortion [%]
VCC = 5.5V VCC = 8.0V 0.01
f = 1kHz 0.01
f = 10kHz
-4
0
4 8 12 16 Output level [dB]
20
-4
0
4 8 12 16 Output level [dB]
20
C type total harmonic distortion-1 (CXA1561)
Encode Mode VCC = 6.0V 0dB = Dolby Level
C type total harmonic distortion-2 (CXA1560)
Encode Mode f = 1kHz 0dB = Dolby Level
1.0
1.0
Distortion [%]
f = 10kHz
Distortion [%]
0.1
f = 100Hz
VCC = 5.5V 0.1
VCC = 8.0V f = 1kHz 0.01 -4 0 4 8 12 16 Output level [dB] 20 0.01 -4 0 4 8 12 16 Output level [dB] 20
- 15 -
CXA1560S, CXA1561M/S, CXA1562M/S
NR OFF total harmonic distortion-3 (CXA1561)
Encode Mode f = 1kHz 0dB = Dolby Level 0.1
NR OFF total harmonic distortion-4 (CXA1562)
Encode Mode f = 1kHz 0dB = Dolby Level 0.1
Distortion [%]
Distortion [%]
VCC = 3.5V
VCC = 4.0V 0.01
VCC = 8.0V
0.01
VCC = 8.0V
-4
0
4 8 12 16 Output level [dB]
20
-4
0
4 8 12 16 Output level [dB]
20
B type total harmonic distortion-3 (CXA1561)
Encode Mode f = 1kHz 0dB = Dolby Level 0.1
B type total harmonic distortion-4 (CXA1562)
Encode Mode f = 1kHz 0dB = Dolby Level 0.1
Distortion [%]
VCC = 4.0V
VCC = 8.0V 0.01
Distortion [%]
VCC = 3.5V
VCC = 8.0V 0.01
-4
0
4 8 12 16 Output level [dB]
20
-4
0
4 8 12 16 Output level [dB]
20
C type total harmonic distortion-3 (CXA1561)
Encode Mode f = 1kHz 0dB = Dolby Level
C type total harmonic distortion-4 (CXA1562)
Encode Mode f = 1kHz 0dB = Dolby Level VCC = 3.5V
1.0
1.0
Distortion [%]
VCC = 4.0V 0.1
Distortion [%]
0.01
VCC = 8.0V
VCC = 8.0V
0.01 -4 0 4 8 12 16 Output level [dB] 20 -4 0 4 8 12 16 Output level [dB] 20
- 16 -
CXA1560S, CXA1561M/S, CXA1562M/S
Cross talk
-40 -50 -60 -70 PB ch to ch -80 -90 -100 PB to REC 100 200 500 1k 2k Frequency [Hz] 5k 10k REC to PB REC ch to ch VCC = 6V Input = +10dB Refer to Dolby Level NR OFF
Cross talk [dB]
NR control threshold
14 VCC
VCN-NR control voltage [V]
12 10 8 6 4 2 0 4 6 8 10 12 14 VCC-Supply voltage [V] 16 NR OFF C type VCC 2 B type
MODE control threshold
14 VCC
VCM-MODE control voltage [V]
12 MPX ON 10 8 6 4 2 0 4 6 8 10 12 14 VCC-Supply voltage [V] 16 PB VCC 2 MPX OFF
- 17 -
CXA1560S, CXA1561M/S, CXA1562M/S
Package Outline
Unit: mm
CXA1561M, CXA1562M
24PIN SOP (PLASTIC)
+ 0.4 15.0 - 0.1 24 13
+ 0.4 1.85 - 0.15
0.15
+ 0.3 5.3 - 0.1
7.9 0.4
+ 0.2 0.1 - 0.05
0.45 0.1
1.27
+ 0.1 0.2 - 0.05
0.12 M
PACKAGE STRUCTURE
MOLDING COMPOUND SONY CODE EIAJ CODE JEDEC CODE SOP-24P-L01 SOP024-P-0300-A LEAD TREATMENT LEAD MATERIAL PACKAGE WEIGHT EPOXY/PHENOL RESIN SOLDER PLATING
COPPER ALLOY / 42ALLOY
0.3g
CXA1560S, CXA1561S, CXA1562S
22PIN SDIP (PLASTIC)
+ 0.1 0.05 0.25 -
12
+ 0.4 19.2 - 0.1
22
+ 0.3 6.4 - 0.1
1 1.778
11
0.5 0.1 + 0.15 0.9 - 0.1
+ 0.15 3.25 - 0.2
0.51 MIN
+ 0.4 3.9 - 0.1
PACKAGE STRUCTURE
MOLDING COMPOUND SONY CODE EIAJ CODE JEDEC CODE SDIP-22P-01 SDIP022-P-0300 LEAD TREATMENT LEAD MATERIAL PACKAGE WEIGHT EPOXY RESIN SOLDER PLATING COPPER ALLOY 0.95g
- 18 -
7.62
0 to 15
0.5 0.2
1
12
6.9

▲Up To Search▲

Price & Availability of CXA1560S

	To Download CXA1560S Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .